P-40 Warhawk 1570mm (61.8") Wingspan - ARF from Nexa - NXA1009-001
The Curtiss P-40 Warhawk is an American single-engined, single-seat, all-metal fighter and ground-attack aircraft that first flew in 1938. The P-40 design was a modification of the previous Curtiss P-36 Hawk which reduced development time and enabled a rapid entry into production and operational service. The Warhawk was used by most Allied powers during World War II, and remained in frontline service until the end of the war. It was the third most-produced American fighter of World War II, after the P-51 and P-47; by November 1944, when production of the P-40 ceased, 13,738 had been built, all at Curtiss-Wright Corporation's main production facilities at Buffalo, New York.
The Nexa P-40 Warhawk is a .60 size electric or gas option scale series warbird with a 1570mm wingspan, constructed primarily from balsa wood and covered with a fuel-resistant covering. This ARF requires assembly and installation of your choice of servos and power system, and includes split flaps, painted pilot, machine gun and other scale details. The large battery hatch affords ample room for either electric or gas setups. Impress at your flying field with this iconic stunner!
Visit the Official Nexa P-40 Warhawk 1570mm ARF Discussion Thread on HobbySquawk.com for additional photos, videos, reviews, and customer Q&A.
\n
\n
\nFully Covered and Detailed
The Nexa P-40 Warhawk comes fully covered including simulated panel lines, rivets, nomenclature and weathering detail.
\n
\n
\n
\n
\nScale Details Throughout
There is no shortage of scale details with this P-40 including functional split flaps, machine guns, and painted pilot.
\n
\n
\n
\n
\nPrehinged and Installed Control Surfaces
All control surfaces come out of the box fully prehinged and installed for your convenience.
\n
\n
\n
\n
\nLarge Battery Hatch
The P-40 has a large battery hatch area to fit an array of LiPo battery sizes.
\n
\n
Features:
\nComplete Balsa and lite-ply construction for rigidity and durability
Covered from tip to tail in scale details including weathering, functional split flaps, printed simulated panel lines and rivets
Fiberglass cowling for strength and durability
The hand-painted pilot is ready for your added cockpit details
Some control surfaces come out of the box pre-hinged and installed for convenience
Large battery hatch allows for your chosen electric or gas setup
\nIncludes:
\nNexa P-40 Warhawk 1570mm (61.8") Wingspan - ARF
Fixed, thick wire landing gear. Note: the retracts and shock-absorbing struts shown in the photos are not included, but are available in the spare parts tab
Fuel tank, hardware and servo trays
\nRequires:
\n6 Channel radio - select a minimum 6 channel radio from our Radio Collection
\n6 Channel receiver - select a minimum 6 channel receiver from our Receiver Collection
\nBrushless outrunner motor - we recommend the Admiral GP10 5030-400Kv Brushless Motor
\n60-75 Amp brushless ESC - we recommend the ZTW Mantis G2 65A ESC with 8A SBEC
\n6x standard servos for ailerons, flaps, elevator and rudder - we recommend the Hitec HS-485HB Deluxe Ball Bearing Karbonite Gear Standard Servo Airplane Multi-Pack (6 Servos)
\nElectric retracts - we recommend Nexa Rotating Electronic Main Retract (Set of 2)
\n6 Cell 22.2V 4000 mAh LiPo Battery - we recommend the Admiral 4000mAh 6S 22.2V 40C LiPo Battery with XT60 Connector
\n14x8 or 15x7 3-Blade Electric propeller
6 Cell compatible battery charger - select a minimum 6 cell (6S) charger from our Charger Collection
\n
Gas Requires:
\n2 stroke engine - we recommend the NGH GT17 17cc Two-Stroke Engine
\n2 blade gas propeller - we recommend the APC 15x8 Gas Propeller
\n
\nCustomer Note
Nexa ARF models are constructed out of balsa wood and plywood. These are not foam models. The assembly of balsa wood ARF aircraft requires basic model building skills including the installation of servos, ESC, and motor (or gas engine).